TimeDeatH
New Member
Grass grows, birds fly, sun shines, and brother... I hurt people.
Posts: 516
|
Post by TimeDeatH on May 26, 2009 8:33:04 GMT -5
I'm trying to find some sort of full face mask that will fit under my mich 2000 helmet. I've been shot in the nose before and it killed, so goggles aren't really an option. Also neoprene is cancelled out, because it's already too warm under the helmet. I was wondering if this would work for a mask that fits under a helmet: www.airsoftpost.com/sansei-style-airsoft-profile-airsoft-mask-black-p-24174.html
|
|
|
Post by Hatemonger on May 26, 2009 9:14:45 GMT -5
Mesh masks are not allowed at MIA approved games. You need to find something that is full seal and "ANSI Z87.1, MIL-V-43511C, or ASTM F 1776-01" rated.
|
|
TimeDeatH
New Member
Grass grows, birds fly, sun shines, and brother... I hurt people.
Posts: 516
|
Post by TimeDeatH on May 26, 2009 9:17:42 GMT -5
I suppose I could wear those walmart goggles underneath?
|
|
|
Post by Hatemonger on May 26, 2009 9:47:32 GMT -5
If your on a tight budget and need something really low profile, something like this JT maskwould be your best bet. JT is known for overall good quality, however with this mask being on the low end of the price spectrum you should expect fogging issues. You could most likely find replacement lenses that are "dual paned" (basically two lenses with an air pocket between them) from JT. I would suggest spending some time at JT USAlooking around.
|
|
TimeDeatH
New Member
Grass grows, birds fly, sun shines, and brother... I hurt people.
Posts: 516
|
Post by TimeDeatH on May 26, 2009 10:07:13 GMT -5
I don't know if any JTs will fit with a helmet. I have 2 from when I played paintball, but neither fit the helmet. I bought that same exact mask from walmart you showed me, but it doesn't fit it either. I'm guessing it's the top part, they all have a flat area on the top for where the visor is supposed to go which gets in the way. I know the other one will fit according to this picture: www.swisslink.com/products/product.php?id=640I do have full seal small airsoft goggles that I bought from walmart I can where under the mask. Edit: Found these, but only on 1 site: infinitytactical.com/infinitytactical/product_info.php?products_id=454 They're the same designs as the wire mesh ones just with full seal goggles.
|
|
|
Post by Dahm on May 26, 2009 13:11:19 GMT -5
I don't know if any JTs will fit with a helmet. I have 2 from when I played paintball, but neither fit the helmet. I bought that same exact mask from walmart you showed me, but it doesn't fit it either. I'm guessing it's the top part, they all have a flat area on the top for where the visor is supposed to go which gets in the way. I know the other one will fit according to this picture: www.swisslink.com/products/product.php?id=640I do have full seal small airsoft goggles that I bought from walmart I can where under the mask. Edit: Found these, but only on 1 site: infinitytactical.com/infinitytactical/product_info.php?products_id=454 They're the same designs as the wire mesh ones just with full seal goggles. Could you always just cut a bit off the top of the mask, or heat it and bend the plastic to fit a mask? Sometimes finding a solution through your own means is easier than searching countless hours trying to find a prefab one online.
|
|
|
Post by Libski on May 26, 2009 13:23:16 GMT -5
I wear this under a helmet and it works fine. You can take off the visor and it fits under a helmet without too much trouble. I use a steel pot helmet and it works fine, so it should work well with your helmet too. www.airsoftgi.com/product_info.php?products_id=3136
|
|
TimeDeatH
New Member
Grass grows, birds fly, sun shines, and brother... I hurt people.
Posts: 516
|
Post by TimeDeatH on May 26, 2009 18:22:48 GMT -5
If there is a flat part on the top of the goggles, it won't work. I'm almost positive the last link I provided will work, because the goggles are very close to the face unlike the Scott, Jt, etc.. masks which have about an inch or more of space from the foam to the lens, which makes it impossible to not have an inch or more on the top part, or else the goggles would be tilted and not be able to fit to the face without discomfort.
|
|
|
Post by SWAT A4 on May 26, 2009 18:59:18 GMT -5
They make these... Cheap and effective. When it comes to wearing helmets.... I've been there and done that. And, then you can put that bottom face shield on most other goggles like so:
|
|
TimeDeatH
New Member
Grass grows, birds fly, sun shines, and brother... I hurt people.
Posts: 516
|
Post by TimeDeatH on May 27, 2009 19:12:28 GMT -5
Edit: Fixed.
|
|