|
Post by Hadoken on Sept 15, 2003 16:08:43 GMT -5
M4 RIS : The RIS Strikes BackWhat started with a couple quick snapshots for Minky (wait ya pervs...snapshots of my M4 RIS!!!...sheesh! ) to show off my new Guarder Aimpoint Rep. purchase turned into a nice little photo session I thought I'd share with the community. So...Enjoy As you can see the beast has changed quite a bit since my last M4 RIS post *BANG* -Marui M4 RIS @ 410 FPS -Guarder AN/PEQ 2 w/ 9.6V 1700MAH Battery -Guarder Aimpoint Replica * -Guarder Cantilever Mount * -G&P Barrel Clamp -Surefire G2 Nitrolon Taclight -Hado Brand Cut Carry Handle -Hado Brand "Poor Bastard" Magpull Stay tuned for M4 RIS part III where I'll be adding an ICS SIR + flip up rear sight. Then proceed to beat Viking over the head with it. ;D * Guarder Aimpoint and Cantilever mount purchased from the fine folks at Airsoft Extreme
|
|
|
Post by luke213 on Sept 15, 2003 16:22:35 GMT -5
Hmm Nice I must say, now I want my RIS even more:( But it is really really nice looking gun. SEXY like
Luke
|
|
|
Post by Jacko on Sept 15, 2003 16:33:45 GMT -5
Ooooo.
And you got the Suck Meter patch in there!
|
|
|
Post by xaos on Sept 15, 2003 17:56:29 GMT -5
Much nice. Glad I was on the good side of that bugger at Firebrand
|
|
|
Post by Hadoken on Sept 15, 2003 18:09:28 GMT -5
Thanks for the kind words Gentlemen.
Luke: Which will you opt for, CA or Marui?
Jacko: The Suck Meter needs to be displayed proudly at all times.
Xaos: Luckily for everyone else I switched the stock spring back for Firebrand.
|
|
|
Post by luke213 on Sept 15, 2003 18:28:00 GMT -5
I went for the CA got a great deal on it(in my opinion) payed basically what I would have for a Marui, from again as stated many times:) My favorite retailer(nothing against WTS-Mike) Zorks.com, with their good ol payment plan. Ordered, the CA M15A4 RIS, 2 KSC Glock 18c's, Standard Glock 18 mag, Highcap Glock Mag, 5 G&P midcap M16 mags. So it should be a pretty good loadout, cost me about $800 even for the whole shot. So a couple hundred a month for three months:) That payplan will be the death of me:)
Luke
P.S. I figured I would chance the internals since I haven't heard bad yet, and getting metal body with metal RIS and everything, all snazy like, though I still feel the need for a SIR, so at some point I may do some switching of guns to allow the purchase of a SIR and a metal M4 probably a CA if this one holds out ok. Hell maybe in 3 months I'll just buy a new something to add to the collection:)
|
|
|
Post by Petary791 on Feb 5, 2004 18:49:27 GMT -5
Does that thing have DUCT TAPE on it!?
if it did you'd be my hero
|
|
Shogo0788
New Member
~Xbox live tag~
Posts: 102
|
Post by Shogo0788 on Feb 5, 2004 18:52:48 GMT -5
Yeah it does have duct tape but i think it is holding something onto the clip. What those 3 lil things on the bottom of the clip are, i have NO idea. What are they?
|
|
|
Post by Viking on Feb 5, 2004 18:54:23 GMT -5
It cords, they are pull handles for the mags, when you have a vest full (most AR15 vest hold 3 mags) it’s quite a tight fit. The pull tabs make for getting your precious ammo out of your vest and into your gun.
|
|
Shogo0788
New Member
~Xbox live tag~
Posts: 102
|
Post by Shogo0788 on Feb 5, 2004 18:57:37 GMT -5
Wow just a few pieces of duct tape and those tabs and *bam* that could save your hide out on the field. That is a kewl "ad-on" that i will be using for my AEG.
|
|
|
Post by WarmongeR on Feb 5, 2004 20:13:08 GMT -5
Its a poor mans mag-pull ,soldiers use paracord (available at any army surplus) and 100 mile an hour tape (or duct tape) to make mag pulls....
|
|
|
Post by Kung Fu on Feb 6, 2004 11:18:21 GMT -5
Great pics! Poor army dude
|
|
|
Post by luke213 on Feb 6, 2004 15:14:21 GMT -5
It's not as much as issue of poor moreso that it's effective. It may not look as *good* as other solutions, but when you consider it doesn't change the mag profile as much as the ones that hold on the mags that are rubber, it's really a pretty good solution. I say moreso with combat then airsoft it's all about function, how you look doesn't come into play, which could be one of the fundamental differences.
Luke
|
|
|
Post by Kung Fu on Feb 10, 2004 0:22:51 GMT -5
Hey Hado, correct me if im wrong, but that looks like sf BDU's with the pocket on the arm. If they are where did you get them?
|
|
|
Post by Motown on Feb 10, 2004 0:47:22 GMT -5
You can buy similar BDU's through Galls and Specwargear, however, you could just do it like the real-life counter parts. Take off the lower pockets on the BDU jacket, and sew them on the sleeves.
|
|